![\"\u0628\u0631\u0634](\"https:\/\/www.mahjamglass.ir\/mag\/wp-content\/uploads\/2019\/05\/\u0628\u0631\u0634-\u0634\u06cc\u0634\u0647-\u0628\u0627-\u0647\u0648\u06cc\u0647-min.jpg\")
<\/p>\nSpecial tools such as diamonds can be used to cut glass. But sometimes these tools are not found at home and we can try cutting glass without tools.<\/p>\n
<\/p>\n
It is also sometimes difficult to cut arched glass, such as glass bottles using diamonds.<\/p>\n
We use the following methods for this purpose:<\/p>\n
Cutting glass with Soldering iron<\/p>\n
Using Soldering iron for cutting glass is one of the most creative and low-risk ways to cut glass.<\/p>\n
To do this, we will perform the following steps:<\/p>\n
First, specify the place where the glass is cut with a marker.<\/p>\n
2. If possible, line the cuts with a knife or diamond to make the work easier.<\/p>\n
3. Hold the Soldering iron at one point to start the crack on the glass.<\/p>\n
4. After cracking, move slowly in the same direction until cracking continues.<\/p>\n
5. When you reach the angled points of the design, lower the Soldering System gently until the glass leaves the strainer.<\/p>\n
6. Slowly remove the cut section.<\/p>\n
7. At the end, remove the unevenness with the sandpaper to remove any roughness.<\/p>\n
<\/p>\n
Cut glass with candles<\/p>\n
This method is almost similar to the previous method.<\/p>\n
However, this method is not very suitable for high-angle designs.<\/p>\n
1. Similar to cutting with Soldering iron, we first draw the pattern on the glass.<\/p>\n
2. Using a diamond or a spatula, draw a line drawing.<\/p>\n
3. Turn on the candle and place the line you draw them on the candle flame.<\/p>\n
4. The cutting site is cracked and the glass is removed.<\/p>\n
5. After it , remove the roughness.<\/p>\n
![\"\u0628\u0631\u0634](\"https:\/\/www.mahjamglass.ir\/mag\/wp-content\/uploads\/2019\/05\/\u0628\u0631\u0634-\u0634\u06cc\u0634\u0647-\u0628\u0627-\u0634\u0645\u0639-min.jpg\")
<\/p>\n
Cutting glass with oil and water<\/p>\n
In this way we do not need any special tools and only water, oil and a bowl are needed.<\/p>\n
This method is usually used to cut glass bottles.<\/p>\n
1. Put bottle in a bowl.<\/p>\n
2. Fill the container to the point where we want it cut.<\/p>\n
3. Fill the bottle exactly as much as the height of the water inside the bottle.<\/p>\n
4. Gradually add the oil to the water until a thin layer of oil stay the surface.<\/p>\n
5. Heat a metal blade until it is completely fried.<\/p>\n
6. Slowly put the blade into the bowl and place under the oil.<\/p>\n
7. If you have done the steps correctly you will hear the glass crackle.<\/p>\n
![\"\u0628\u0631\u0634](\"https:\/\/www.mahjamglass.ir\/mag\/wp-content\/uploads\/2019\/05\/\u0628\u0631\u0634-\u0634\u06cc\u0634\u0647-\u0628\u0627-\u0622\u0628-\u0648-\u0631\u0648\u063a\u0646-min.jpg\")
<\/p>\n
<\/p>\n
MahjamGlass manufacturer of all kinds of mirror models.<\/p>\n
Design from you, build from us.<\/a><\/p>\n You can decorate your home like a palace.<\/p>\n <\/p>\n Connect with us on social networks:<\/p>\n Iniestagram MahjamGlass <\/a><\/p>\n LinkedIn <\/a>MahjamGlass<\/a><\/p>\n MahjamGlass<\/a> Telegram Channel<\/a><\/p>\n And if you need email addresses and phone numbers, visit our contact page:<\/p>\n